511 found, showing page 3 of 13
$3.89
1G GY WP PLST BL COVER
Blank outdoor box cover. Ideal for general use when weatherproof protection is needed. Constructed of durable, high impact polycarbonate. Includes attached gasket and mounting hardware. NEMA (National Electrical Manufacturers Association) 3R rated.
View Details
$16.49
2" RIGID OFFSET
Rigid offset nipple, pressure cast. 1 each. UPC coded. UL listed.
View Details
$2.39
STAPLE CABLE 1/2"
Made from high-grade injection molded plastic with high-dielectric strength. Smooth saddle prevents damage to insulation. Tested for a maximum 70-pound pull. 15 per card.
View Details
$3.99
3-1/2 X 1-1/2 DP OCT BOX
Steel, octagon, electrical box. Ideal to house lightweight fixtures or safety devices in ceilings. UL (Underwriter's Laboratories) listed.
View Details
$7.19
*COVR RND OUTDR GY
Round cluster cover for use with lampholders. (1) 1/2-inch threaded outlet. Made of corrosion resistant zinc, finished with a protective color coating. For wet locations, gaskets and screws included. Carded. Gray. UL (Underwriter's Laboratories) listed.
View Details
$7.39
1/2" INSULATED STAPLE
Cable staple ideal for use with all 2-wire UF, non-metallic, and BX cable. 1/2-inch unbreakable clear poly construction, will not bruise wires.
View Details
$6.29
2" BOX CONNECTOR
Clamp type. Die-cast body. UPC coded. UL listed.
View Details
$8.69
3/4" INSULATED STAPLE
Cable staple ideal for use with 3-wire UF, non-metallic, and BX cable. 3/4-inch unbreakable clear poly construction.
View Details
$5.39
1-1/2" BOX CONNECTOR*****
Clamp type. Die-cast body. UPC coded. UL listed.
View Details
$8.19
5' SPLIT FLEX TUBING
Made of tough black polyethylene extrusion which is corrugated for maximum flexibility and is split along its length for easy use and management of multiple wire runs. Poly bag with header for hanging on a peg hook.
View Details
$17.49
*FIXTURE RECESSED***************
Recess housing for remodel construction. Thermally protected housing, pre-wired, UL (Underwriter's Laboratories) listed for damp locations. Ideal for exterior use. IC (insulation contact) rated for use in direct contact with thermal insulation with trims accepting up to 75 watts - 90 watt maximum lamp when used with Model No. TRB30 trim. Use with trims accepting up to 150 watts in NON-IC applications. Features adjustable socket plate that can be removed for use with fully enclosed trim. Ceiling opening 6-1/4 inches. For use with most Thomas 6 inch recess trims.
View Details
$6.19
1/2" LIQTITE CONNECTOR
Multi-piece straight liquidtight connector. Die-cast zinc. 1 per bag. UPC coded. UL listed.
View Details
$2.69
4" 1-GANG RISER 5/8
Steel, 4" square combination, covers 1 device. UL listed.
View Details
$10.49
3/4" LIQTITE CONNECTOR
Multi-piece straight liquidtight connector. Die-cast zinc. 1 per bag. UPC coded. UL listed.
View Details
$1.04
10/2 W/G NMB ROMEX WIRE 250'
Type NM-B cable is designed specifically for use in residential and commercial wiring of branch circuits. Installation above ground and in dry locations only. Approved for service to 600 volts. PVC (polyvinyl chloride) jacket and PVC insulated, nylon jacketed conductors. Flame-retardant and crush-resistant. UL (Underwriter's Laboratories) listed.
View Details
$8.89
1/2" LIQTITE CONNECTOR
Multi-piece 90-degree liquid tight connector. Die-cast zinc. 1 each. UPC coded. UL (Underwriter's Laboratories) listed.
View Details
$13.99
3/4" LIQTITE CONNECTOR
Multi-piece 90-degree liquid tight connector. Die-cast zinc. 1 each. UPC coded. UL (Underwriter's Laboratories) listed.
View Details
$8.88
1/2" SCH40 10' PVC CONDUIT
Rigid PVC plastic conduit. Proven durable and effective for years of maintenance free performance in underground, encased, and exposed applications in accordance with the National Electrical Code.
View Details
$2.59
1" RGD 2-HOLE STRAP 4-PK
4PK 1" RGD 2-HOLE STRAP
View Details
$10.98
3/4" SCH40 10' CONDUIT
Rigid PVC plastic conduit. Proven durable and effective for years of maintenance free performance in underground, encased, and exposed applications in accordance with the National Electrical Code.
View Details
$15.28
1" SCH40 10' CONDUIT
Rigid PVC plastic conduit. Proven durable and effective for years of maintenance free performance in underground, encased, and exposed applications in accordance with the National Electrical Code.
View Details
$22.88
1-1/4" SCH40 10' PVC CONDUIT
Rigid PVC plastic conduit. Proven durable and effective for years of maintenance free performance in underground, encased, and exposed applications in accordance with the National Electrical Code.
View Details
$0.99
14/2 W/G NMB ROMEX WIRE 1000'
Type NM-B cable is designed specifically for use in residential and commercial wiring of branch circuits. Installation above ground and in dry locations only. Approved for service to 600 volts. PVC (polyvinyl chloride) jacket and PVC insulated, nylon jacketed conductors. Flame retardant and crush-resistant. UL (Underwriter's Laboratories) listed.
View Details
$1.19
12/2 W/G NMB ROMEX WIRE 1000'
Type NM-B cable is designed specifically for use in residential and commercial wiring of branch circuits. Installation above ground and in dry locations only. Approved for service to 600 volts. PVC (polyvinyl chloride) jacket and PVC insulated, nylon jacketed conductors with ground (WG). Flame-retardant and crush-resistant. UL (Underwriter's Laboratories) listed.
View Details
$1.29
*3/8" FLEX CONNECTOR
Screw-in, non-insulated, die-cast zinc connector. For use with armored cable and flexible metallic conduit. UL (Underwriter's Laboratories) listed.
View Details
$0.79
1/2" COUPLING
Socket-type conduit coupling. Ideal for jointing PVC (polyvinyl chloride) conduit. Requires solvent cement. UL (Underwriter's Laboratories) listed.
View Details
$0.89
3/4" COUPLING
Socket-type conduit coupling. Ideal for jointing PVC (polyvinyl chloride) conduit. Requires solvent cement. UL (Underwriter's Laboratories) listed.
View Details
$1.29
1" PVC COUPLING SCH40
Socket-type conduit coupling. Ideal for jointing PVC (polyvinyl chloride) conduit. Requires solvent cement. UL (Underwriter's Laboratories) listed.
View Details
$3.29
2" CONDUIT HANGER
For EMT, IMC, and rigid conduit. With bolt assembly. UPC coded.
View Details
$1.59
*COUPLING 1-1/4" PVC
Socket-type conduit coupling. Ideal for jointing PVC (polyvinyl chloride) conduit. Requires solvent cement. UL (Underwriter's Laboratories) listed.
View Details
$1.79
HANGER COND 1-1/2"
Conduit hanger for use with rigid and IMC conduit.
View Details
$1.79
1-1/4" CONDUIT HANGER
For EMT, IMC, and rigid conduit. With bolt assembly. UPC coded.
View Details
$0.99
HANGER COND 1/2"
For EMT, IMC, and rigid conduit. With bolt assembly. UPC coded.
View Details
$8.49
1/2"x10' EMT PIPE
Allied Tube EMT (Electrical Metal Tubing) is precision manufactured from high grade, mild strip steel for exceptional durability and longevity. Constructed of hot galvanized steel using a patented inline Flo-Coat process which combines zinc, a conversion coating, and clear organic polymer topcoat forming a triple layer of protection against corrosion and abrasion. E-Z Pull EMT combines strength with ductility, providing easy bending, cutting, and joining while resisting flattening, kinking, and splitting. UL (Underwriter's Laboratories) 797 Listed and manufactured in accordance with ANSI (American National Standards Institute) C80.3. 10-foot lengths. Order in full lengths only. Made from USA steel.
View Details
$15.99
3/4"x10' EMT PIPE
Allied Tube EMT (Electrical Metal Tubing) is precision manufactured from high grade, mild strip steel for exceptional durability and longevity. Constructed of hot galvanized steel using a patented inline Flo-Coat process which combines zinc, a conversion coating, and clear organic polymer topcoat forming a triple layer of protection against corrosion and abrasion. E-Z Pull EMT combines strength with ductility, providing easy bending, cutting, and joining while resisting flattening, kinking, and splitting. UL (Underwriter's Laboratories) 797 Listed and manufactured in accordance with ANSI (American National Standards Institute) C80.3. 10-foot lengths. Order in full lengths only. Made from USA steel.
View Details
$22.88
1"x10' EMT PIPE
Allied Tube EMT (Electrical Metal Tubing) is precision manufactured from high grade, mild strip steel for exceptional durability and longevity. Constructed of hot galvanized steel using a patented inline Flo-Coat process which combines zinc, a conversion coating, and clear organic polymer topcoat forming a triple layer of protection against corrosion and abrasion. E-Z Pull EMT combines strength with ductility, providing easy bending, cutting, and joining while resisting flattening, kinking, and splitting. UL (Underwriter's Laboratories) 797 Listed and manufactured in accordance with ANSI (American National Standards Institute) C80.3. 10-foot lengths. Order in full lengths only. Made from USA steel.
View Details
$1.49
1" CONDUIT HANGER
For EMT, IMC, and rigid conduit. With bolt assembly. UPC coded.
View Details
$1.99
1-1/2" COUPLING
Socket-type conduit coupling. Ideal for jointing PVC (polyvinyl chloride) conduit. Requires solvent cement. UL (Underwriter's Laboratories) listed.
View Details
$1.29
1/2" FLEX COUPLING
Screw-in type coupling for flexible metal conduit. Die-cast zinc. UL (Underwriter's Laboratories) listed.
View Details
$2.39
2" COUPLING
Socket-type conduit coupling. Ideal for jointing PVC (polyvinyl chloride) conduit. Requires solvent cement. UL (Underwriter's Laboratories) listed.
View Details
