219 found, showing page 2 of 15
$4.79

8x12 ROLLER TRAY
Whizz Solvent-Resistant Paint Tray is made of injection molded 100\% virgin polypropylene for stability. Clear. 6 In. tray for rollers up to 4 In., 8 In. tray for rollers up to 6 In.
View Details
$10.99

4" ROLLER & TRAY SET
Set contains a trim roller frame with 2 Nonstick roller covers. 3/8" nap and a plastic trim tray. Nonstick coated rollers work clean and fast. Paint sticks to the wall, not on the roller. Made for use with all paints.
View Details
$5.99

2GL METAL PAINT RLR GRID
The sturdy rust-resistant, plated grid is pre-bent to secure the grid to the side of the bucket. The bottom of the grid ramp keeps the grid stable as the roller passes across the surface. The grid surface removes excess paint and distributes it evenly on the roller cover to assure a good result on the painting surface 4-sided metal mesh grid.
View Details
$49.99

LATEX CURB PAINT RED
Fast dry marking paints that are designed for streets and parking lots. They may be ambient, airless, conventional, or heated to accelerate the dry time. Normal dry time is 10 minutes at 77 deg. F. at 50\% humidity. These meet or exceed the current VOC regulations and to the requirements of Federal Specification TT-P-01952E Types I and II. Use on cured asphalt, concrete, brick, and other street or highway surfaces. Do not paint on wet surfaces. Dries to a flat finish. Covers approximately 300 to 350 sq. ft. per gallon or approximately 320 lineal ft. with 4" stripe. Do not use brush or roller. Apply with Airless Line Sprayer at 1800 to 2700 P.S.I. with .015 to .019" tip or Conventional Line Sprayer (atomization pressure 20 to 80 P.S.I.) Thin with water up to 12.5\% by volume if needed. Clean hands and tools immediately after use with soap and warm water. Flush spray equipment with mineral spirits to prevent rusting of equipment.
View Details
$7.99

5GL METAL PAINT RLR GRID
The sturdy rust-resistant, plated grid is pre-bent to secure the grid to the side of the bucket. The bottom of the grid ramp keeps the grid stable as the roller passes across the surface. The grid surface removes excess paint and distributes it evenly on the roller cover to assure a good result on the painting surface 4-sided metal mesh grid.
View Details
$53.99

GLS EX DEEP BS LTX PAINT
New and improved interior/exterior, direct to metal (DTM), water-based high gloss acrylic enamel designed for industrial maintenance and construction purposes. Use on machinery, farm implements, fixtures, conveyors, safety equipment, metal, wood, and doors. Provides excellent rust and corrosion resistance. Acceptable for use in federally inspected meat and poultry plants. Use for safety colors for marking in industrial, construction, traffic areas. Surfaces must be clean, dry, and in sound condition. Remove all loose rust, paint, and any contamination to ensure adequate adhesion. For better adhesion, undercoat iron, steel, and aluminum with Do it Best waterborne primer. Allow a minimum of 6 months to weather galvanized steel before priming and topcoating. Masonry and block surfaces should be clean and dust-free and cured for atleast 28 days; fill holes with block filler before topcoating. Apply with a synthetic brush, roller, or airless sprayer. Clean up with soap and water. Covers approximately 300 to 350 sq. ft. per gallon. Dries to touch 20 to 45 minutes or to recoat in 4 to 6 hours.
View Details
$53.99

GLS NEUTRAL BS LTX PAINT
New and improved interior/exterior, direct to metal (DTM), water-based high gloss acrylic enamel designed for industrial maintenance and construction purposes. Use on machinery, farm implements, fixtures, conveyors, safety equipment, metal, wood, and doors. Provides excellent rust and corrosion resistance. Acceptable for use in federally inspected meat and poultry plants. Use for safety colors for marking in industrial, construction, traffic areas. Surfaces must be clean, dry, and in sound condition. Remove all loose rust, paint, and any contamination to ensure adequate adhesion. For better adhesion, undercoat iron, steel, and aluminum with Do it Best waterborne primer. Allow a minimum of 6 months to weather galvanized steel before priming and topcoating. Masonry and block surfaces should be clean and dust-free and cured for atleast 28 days; fill holes with block filler before topcoating. Apply with a synthetic brush, roller, or airless sprayer. Clean up with soap and water. Covers approximately 300 to 350 sq. ft. per gallon. Dries to touch 20 to 45 minutes or to recoat in 4 to 6 hours.
View Details
$5.49

9x3/8 KNIT ROLLER COVER
High quality polyester knit roller cover is for use on both interior and exterior painting projects. High-density knit roller holds more paint than a woven cover making it perfect for large painting projects.
View Details
$6.49

9x3/4 KNIT ROLLER COVER
High quality polyester knit roller cover is for use on both interior and exterior painting projects. High-density knit roller holds more paint than a woven cover making it perfect for large painting projects.
View Details
$5.99

1/2" NAP OC ROLLER COVER
High quality polyester knit roller cover is for use on both interior and exterior painting projects. High-density knit roller holds more paint than a woven cover making it perfect for large painting projects.
View Details
$53.99

GLS PSTL/WHT LATEX PAINT
New and improved interior/exterior, direct to metal (DTM), water-based high gloss acrylic enamel designed for industrial maintenance and construction purposes. Use on machinery, farm implements, fixtures, conveyors, safety equipment, metal, wood, and doors. Provides excellent rust and corrosion resistance. Acceptable for use in federally inspected meat and poultry plants. Use for safety colors for marking in industrial, construction, traffic areas. Surfaces must be clean, dry, and in sound condition. Remove all loose rust, paint, and any contamination to ensure adequate adhesion. For better adhesion, undercoat iron, steel, and aluminum with Do it Best waterborne primer. Allow a minimum of 6 months to weather galvanized steel before priming and topcoating. Masonry and block surfaces should be clean and dust-free and cured for atleast 28 days; fill holes with block filler before topcoating. Apply with a synthetic brush, roller, or airless sprayer. Clean up with soap and water. Covers approximately 300 to 350 sq. ft. per gallon. Dries to touch 20 to 45 minutes or to recoat in 4 to 6 hours.
View Details
$53.99

GLS BLACK LATEX PAINT
New and improved interior/exterior, direct to metal (DTM), water-based high gloss acrylic enamel designed for industrial maintenance and construction purposes. Use on machinery, farm implements, fixtures, conveyors, safety equipment, metal, wood, and doors. Provides excellent rust and corrosion resistance. Acceptable for use in federally inspected meat and poultry plants. Use for safety colors for marking in industrial, construction, traffic areas. Surfaces must be clean, dry, and in sound condition. Remove all loose rust, paint, and any contamination to ensure adequate adhesion. For better adhesion, undercoat iron, steel, and aluminum with Do it Best waterborne primer. Allow a minimum of 6 months to weather galvanized steel before priming and topcoating. Masonry and block surfaces should be clean and dust-free and cured for atleast 28 days; fill holes with block filler before topcoating. Apply with a synthetic brush, roller, or airless sprayer. Clean up with soap and water. Covers approximately 300 to 350 sq. ft. per gallon. Dries to touch 20 to 45 minutes or to recoat in 4 to 6 hours.
View Details
$34.99

YELLOW LATEX TRAFFIC PAINT gal
Fast dry marking paints that are designed for streets and parking lots. They may be ambient, airless, conventional, or heated to accelerate the dry time. Normal dry time is 10 minutes at 77 deg. F. at 50\% humidity. These meet or exceed the current VOC regulations and to the requirements of Federal Specification TT-P-01952E Types I and II. Use on cured asphalt, concrete, brick, and other street or highway surfaces. Do not paint on wet surfaces. Dries to a flat finish. Covers approximately 300 to 350 sq. ft. per gallon or approximately 320 lineal ft. with 4" stripe. Do not use brush or roller. Apply with Airless Line Sprayer at 1800 to 2700 P.S.I. with .015 to .019" tip or Conventional Line Sprayer (atomization pressure 20 to 80 P.S.I.) Thin with water up to 12.5\% by volume if needed. Clean hands and tools immediately after use with soap and warm water. Flush spray equipment with mineral spirits to prevent rusting of equipment.
View Details
$39.99

LATEX TRAFFIC PAINT WHITE
Fast dry marking paints that are designed for streets and parking lots. They may be ambient, airless, conventional, or heated to accelerate the dry time. Normal dry time is 10 minutes at 77 deg. F. at 50\% humidity. These meet or exceed the current VOC regulations and to the requirements of Federal Specification TT-P-01952E Types I and II. Use on cured asphalt, concrete, brick, and other street or highway surfaces. Do not paint on wet surfaces. Dries to a flat finish. Covers approximately 300 to 350 sq. ft. per gallon or approximately 320 lineal ft. with 4" stripe. Do not use brush or roller. Apply with Airless Line Sprayer at 1800 to 2700 P.S.I. with .015 to .019" tip or Conventional Line Sprayer (atomization pressure 20 to 80 P.S.I.) Thin with water up to 12.5\% by volume if needed. Clean hands and tools immediately after use with soap and warm water. Flush spray equipment with mineral spirits to prevent rusting of equipment.
View Details
$164.99

YELLOW LATEX TRAFFIC PAINT
Fast dry marking paints that are designed for streets and parking lots. They may be ambient, airless, conventional, or heated to accelerate the dry time. Normal dry time is 10 minutes at 77 deg. F. at 50\% humidity. These meet or exceed the current VOC regulations and to the requirements of Federal Specification TT-P-01952E Types I and II. Use on cured asphalt, concrete, brick, and other street or highway surfaces. Do not paint on wet surfaces. Dries to a flat finish. Covers approximately 300 to 350 sq. ft. per gallon or approximately 320 lineal ft. with 4" stripe. Do not use brush or roller. Apply with Airless Line Sprayer at 1800 to 2700 P.S.I. with .015 to .019" tip or Conventional Line Sprayer (atomization pressure 20 to 80 P.S.I.) Thin with water up to 12.5\% by volume if needed. Clean hands and tools immediately after use with soap and warm water. Flush spray equipment with mineral spirits to prevent rusting of equipment.
View Details